A hybrid heat pump water heater pulls heat from the surrounding air to warm the tank, with electric elements as backup. When one stops making hot water, the fix can be as small as a control board or as big as a new water heater. Here is how we sort that out, based on two Mercer Island jobs from this November.
First, a few things to check yourself
- Look at the display. Most hybrids show an alert or error code. Write it down or take a photo before you reset anything.
- Check the breaker. Hybrids run on a 240-volt circuit, and a tripped breaker shuts everything off.
- Clean the air filter. A clogged filter starves the heat pump of air and can trigger alerts or slow recovery.
- Check the mode. If someone switched the unit to vacation or a heat-pump-only mode, it may not keep up with a busy household.
- Look for water around the base. A clogged condensate drain can cause alerts; a leak from the tank itself is a different story.
If none of that explains it, the unit needs a proper diagnosis. Error codes point in a direction, but they do not always name the failed part.
When a control board repair makes sense
The control board runs the compressor, fan, expansion valve, elements and sensors. When it fails, the tank and the heat pump can be perfectly healthy. That makes a board one of the better repairs on a hybrid.
In November we looked up the control board for a Rheem ProTerra 80-gallon hybrid in Mercer Island. The manufacturer's service manual lists board replacement as the fix for specific error codes, clock errors and a Wi-Fi communication error. It also warns against swapping the board for other symptoms until the testing points to it. For example, if the fan is getting power but not running, the problem is the fan, not the board.
A board repair usually makes sense when:
- Testing confirms the board is the failed part, not a sensor, fan or wiring issue.
- The tank is not leaking and the compressor runs.
- The unit is still well within its expected life, or still under the manufacturer's parts warranty. Check the serial number before you buy anything.
When to replace the hybrid
Some failures cost more to fix than the unit is worth. Replacement is usually the better call when:
- The tank is leaking. A leaking tank cannot be repaired.
- The sealed refrigeration system has failed, such as the compressor, and the unit is out of warranty.
- The unit is older and this is not its first major repair.
- It has never kept up with your household, and you were already thinking about a change.
If you liked having a hybrid, a new one is often a simple swap. The wiring, drain and space are already in place.
When going tankless is the better choice
On November 20 we replaced a different hybrid heat pump water heater in Mercer Island whose compressor had failed (see the before and after photos). It sat in a mechanical room beside the furnace. The homeowner chose not to put money into a sealed-system repair and went with a Navien condensing gas tankless water heater, rated at 199,000 BTU, with a recirculation pump built in.
The part most people do not expect is the gas line. A tankless burner uses far more gas at once than a tank does, so we ran a larger gas line to the unit. We also installed a tankless valve set with service valves so the heater can be flushed during regular maintenance.
Gas tankless tends to be the better fit when:
- The home already has natural gas, and the gas service and piping can be upsized for the burner.
- You want endless hot water for back-to-back showers or a large soaking tub.
- Wall space is tight. A tankless frees up the floor space a tank uses.
- The hybrid's location was a poor match, such as a small or closed room where the heat pump did not have enough air.
A hybrid can be the better fit when you want an all-electric home, there is no gas service, or the rebate below makes a new hybrid the clear value.
The PSE rebate on a new hybrid
Puget Sound Energy currently offers $1,000 back on qualifying Tier 3 or Tier 4 heat pump water heaters for PSE electric customers in existing single-family homes. Income-qualified customers in PSE's Efficiency Boost program can get a higher amount.
- The model has to be on PSE's qualified product list.
- The application has to be submitted within 30 days of installation.
- You need the paid installation invoice and receipt, showing the install date, brand and model number.
- Equipment replaced under warranty does not get a second rebate.
Rebates change, so check PSE's heat pump water heater rebate page for the current terms before you decide. A gas tankless does not qualify for this heat pump water heater rebate, so factor that into the comparison. For more on the trade-offs, see tankless vs. tank water heaters. Other utility, state and federal incentives may also apply.
What we recommend
- Get a real diagnosis before buying parts. A board, a sensor and a fan can all look like the same problem.
- Repair when the failed part is confirmed, the tank is sound and the unit has life left.
- Replace when the tank leaks or the sealed system fails out of warranty.
- Consider gas tankless when you have gas service, want endless hot water and are ready for a gas line upgrade.
OutToday has been repairing and replacing water heaters across Bellevue, Mercer Island and the Eastside since 1989. A technician will tell you which option fits your home and confirm the price in writing before any work begins.
Want a professional opinion?
Call us any time, day or night, at (425) 615-5000, or book online. Written pricing before any work begins.
Related services:
